Hopkins shield tile grouts I. Introduction 1. The product has good adhesion and flexibility performance impermeability crack, make decorative panels waterproof overall increase for caulking tile, stone and other decorative materials. 2. Colorful decorative panels make more perfect decorative effect. 3, a waterproof mildew features to make decorative health, clean. 4, can reduce the anti-pulp, tears and other phenomena linked to pollution finishes. Two colors: white, yellow, red, green, blue and other 15 kinds of three technical indicators perform JC / T 1004-2006 standard indicators. Fourth, the base surface treatment: a gap to be clean and free of debris and water, for higher water absorption of tiles, can be pre-wet slit. 2. Make sure to dry completely after the tile adhesive (about 24 hours) before proceeding caulk. Fifth, use: 1, clean need to caulk the gap, making no dust, debris and water. 2, the depth of the gap to be less than 0.6 cm or brick high. 3, the aperture is too large pores of tile, protection should be made after finishing caulk to affect or contaminate tile, caulk or grout with a special knife. 4, the Hopkins shield color waterproof sealant mildew by 3.3 to 3.5: 1 (powder: water) with no more than stir into cream burnt-like particles, let stand 3 to 5 minutes and then stir 1 to 2 minutes can be used. 5, with a rubber sealing knife or scraper soft, waterproof mildew marinated colored tile sealant along the diagonal direction pressed into crevices to fill the gap, and scrape away the excess part of the construction time 1 to 2 hours. 6, let it dry naturally after, depending on the weather about 2 to 6 hours, with a damp sponge or cloth to clean the tile surface. 7, to be completely cured sealant for 24 hours, then water or special cleaning agents remove remaining stains. VI Notes: 1, powder, water ratio, depending on the width of the cracks between the blocks and the dryness of the environment mildew waterproof sealant is slightly different, relatively narrow gap a little thin, brick slot width should be 1.5 to 5 mm ( When using grit caulks, Zhuanfeng width of 2 to 13 mm). 2, can not use acidic cleaners to clean tile caulk has. 3, can not and under construction in rainy conditions than 5 ~ 40 ℃. 4, in the expansion joints should be neutral, and other special glue sealant. 5, the construction of try not to have too thick sealant remains in the brick, so as not to difficult to clean after bonding. 6, within 24 hours to avoid on the tile caulk and sealant pressure, scratching and rain. 7, after the black sealant construction as soon as possible (within 10 minutes) with a dry cloth to clean the base surface. Wait 24 hours to dry before they can clean the remaining stains with water, so as not to produce white sealant. 8, when the large-scale construction, expansion joints should stay, 5 to 6 hours after application needs conservation 1, 24 hours after curing 2nd. Seven, the amount calculated as follows: Aperture size bricks per square meters deep seam amount 95㎜ 3 mm × 5 mm 0.58㎏ 95㎜ 240㎜ 60 mm × 5 mm × 5 mm 200 mm 300 mm 5 mm 5 mm 1.15㎏ 0.3㎏ 400 mm 5 mm × 400 mm × 7 mm 600 mm 600 mm 5 mm 7 mm 0.32㎏ 0.21㎏ eight, Storage: Store in a cool dry place, unopened product can be stored for 18 months. Nine, Packing: 24 kg / box, 2 kg / bag Hopkins Shield waterproof, waterproof coatings, waterproofing materials Recruitment agents throughout the country's top ten brands